Search results

  1. M

    Power Steering Cap Gasket?

    My Dorman 82585 came with a flat neoprene gasket as pictured ... and upon reinspecting my original cap, it has a flat ring gasket as well. It just really looks and feels like plastic until I probe the edge with a toothpick.
  2. M

    Gen 1 Audio Upgrade Thread.

    9) Remove four screws on back of stanchions. Remove three screws on front stanchion. The seat belt mount prevents the stanchion from coming off. 10) Time to remove the big seatbelt bolt. Start by unclipping the triangular seat belt trim piece. There's a tab on each side. It has to be worked a...
  3. M

    Gen 1 Audio Upgrade Thread.

    Door speakers part 3. 6) Three mounting screws. These are screwed in horizontally via tabs that are mostly visible. The short screw is the front-most screw. The other two are the same size. Two are shown below. The last is on the bottom towards the rear of the car. My screw driver is pointing...
  4. M

    Gen 1 Audio Upgrade Thread.

    Door speakers part 2: My photos will not always be from the same side. I sometimes put screws back in the holes they came from in order to keep track of them. Tools: #2 philips screw driver T50 socket I recommend a Finger Grip bit driver (i.e.: super-stubby screw driver) 1) Remove door pull...
  5. M

    Gen 1 Audio Upgrade Thread.

    First up is door speakers. Items bought: A pair of Kicker 5.25" 4 ohm speakers. Model #: 46CSC54 A pair of Silicone 5.25" Car Speaker Baffles. Brand: Recoil. Model #: SPB525. I'm sure there are many like this A pair of Bass Blockers. I chose one that eliminates frequencies between 0-5.6kHz at...
  6. M

    Gen 1 Audio Upgrade Thread.

    I'm starting a thread for my audio upgrades on my 1993. Gen 2 seems to be well documented in various places, but I figured Gen 1 is different enough to warrant some posts. My goals are: 1) Door midrange speakers (See posts 2 3 4 5) 3) Door tweeter speakers (See post 7) 3) Rear speakers...
  7. M

    Power Steering Cap Gasket?

    Thanks. I previously checked my cap. It had the rubber flap, but no rubber ring. I ordered a Dorman 82585 cap. Hopefully it has a rubber ring. I will find out thursday. I routed a 3/8 fuel line from the breather on my cap to under the brake booster. My understanding is that with the hose fixed...
  8. M

    Power Steering Cap Gasket?

    Does anyone know if the gen 1 and 2 power steering caps are supposed to have a gasket or o-ring? If so, does anyone know a part number or correct o-ring size? I've been finding conflicting information....
  9. M

    3D print an interior door sill plug

    I updated the printables.com link with an "inner" and "outer" plug.
  10. M

    3D print an interior door sill plug

    Ohhh.... I found a photo. I had no idea there was supposed to be plugs over those screws. I don't have a single one. Well dang... Guess I'll make those next.
  11. M

    3D print an interior door sill plug

    There might be some confusion on which plugs these are. They're under the door when the door is closed. There's 4 per side on my 93. I circled 3 in green on the driver's side in this photo (ignore the messy garage!):
  12. M

    3D print an interior door sill plug

    When working on the exhaust, you pull them out to access the bolts holding the rocker panels on. I was missing 3 when I bought the car.
  13. M

    Need Some Maintenence Help with '95 1st GEN

    I'm not sure I quite understand your questions, but in terms of Q1, the gap on the right side of the hood is so you can slip your hand in and undo the hood latch. It's supposed to be there. But there is some sort of misalignment going on there. I can't tell if the driver's side of the hood is...
  14. M

    3D print an interior door sill plug

    These should work for 1992 - 2000 This was supposed to be a quick and easy design, but it took some effort to get the button/dome top to not look crummy and to align the layer lines so the legs wouldn't snap off.... Photos and instructions are on the printables.com link below, but In short...
  15. M

    What did you do to your Viper today?

    Viper driving season was over in November in Vancouver, BC. I'm doing less interesting work, but since you asked... :p On my 93 antenna car, the giant antenna gets in the way of the car cover. I managed to find a Metra 44-STUB antenna that comes with the elusive female 1/4-20 to male 6mm...
  16. M

    3D print an Air Filter Intake Box Retainer

    I couldn't find a replacement part. I had been using a rubber washer with a squared hole to hold the intake baffle in place. I made a replacement you can print in a flexible filament. More photos are on the printables.com link...
  17. M

    Sometimes stalls when coming to a stop.

    Thanks @vprtech That's valuable advice and background information. My car is now stored for the winter, but I will re-adjust it when the weather warms up.
  18. M

    New Gen 1 Stanchions are now available

    @ninetyfive for what it's worth, I had the same problem. Here's how I repaired it: Mix 50% baking soda and 50% graphite powder. Graphite powder can be made by splitting open a standard wooden pencil and grinding the graphite stick against sand paper into powder. Mask the front (or visible...
  19. M

    How to replace an IAC motor on a Gen 1

    You can see my thread here on what I'm trying to solve: https://www.viperclub.org/vca/threads/sometimes-stalls-when-coming-to-a-stop.678665/#post-3307119 However in my case, I was wrong to change this part. My existing part was fine. Generally speaking, symptoms of a bad IAC motor would be an...
  20. M

    Sometimes stalls when coming to a stop.

    Thanks all for your replies. I've had a busy week so I've been slow to work on this problem. I haven't touched the throttle position stop screws. I looked at both throttle bodies and both have the plates stop just behind the first small hole in the bottom of the throttle body. I added Lucas...
  21. M

    Sometimes stalls when coming to a stop.

    Thanks. It's a good point that the gauge may not be accurate. I ran across another thread where someone said the RPM reading from the gauge was lower than whattheir scanner was reporting. I haven't looked at the MAP sensor yet. I understand there's 3 wires. 5v supply, ground and the middle wire...
  22. M

    How to replace an IAC motor on a Gen 1

    The Idle Air Control (IAC) motor is on the back of the intake on the passenger side. You may be wondering if you can actually get it off without removing the intake. Yes you can. Here's how. Tools: 7/16 regular wrench. 7/16 stubby wrench. It's in a tight spot and a regular wrench will hit a...
  23. M

    Sometimes stalls when coming to a stop.

    I have a 1993. As the title says, when coming to a stop my rpms will drop to near zero. It's even stalled a couple of times. At operating temperature the idle seems low. It shows closer to 575 that 704+-25. Yes I am reading the gauge correctly. Yes I realize the first mark just after 0 is...
  24. M

    3D print a case for an ELK-960 timed relay

    Published here: https://www.printables.com/model/526850-elk-960-case I came across this post: https://www.viperclub.org/vca/threads/how-to-build-a-primer-timer-and-cure-your-viper-fuel-pump-starting-problem.624994/ which describes using a timed relay to work around slow-start problem. Though I...
  25. M

    How to build a Primer Timer and cure your Viper Fuel Pump Starting Problem

    For what it's worth, I made a printable ELK-960 box. https://www.printables.com/model/526850-elk-960-case

Latest posts

Members online

Total: 1,275 (members: 7, guests: 1,268)

Forum statistics

Threads
153,609
Posts
1,684,960
Members
18,178
Latest member
wrm92

Share this page

Top