Getting upgrades 2000 RT/10

Kebin F Friel

Enthusiast
Joined
Mar 25, 2021
Posts
10
Reaction score
4
Location
30019
I have a steel gray 2000 RT/10 25,000 miles (not sure how many were made in gray) but getting upgrades part finally in. Just baught a few months ago.

New Ball Joints
Belanger Complete Exhaust
K & N Performance Air Intake
SCT X3 Power Flash Programmers
Dyno Tuning

Dropping off Friday cant wait. Any suggestions for the next upgrades. Just found a soft top w/ frame. Need new wheels and tires.

You must be registered for see images attach


You must be registered for see images attach
 

BadBrad72

Enthusiast
Joined
Jun 19, 2010
Posts
12
Reaction score
4
They are one of the rare colours.
I have one up here in Canada that colour.
Fidanza light weight flywheel with replaceable friction discs made the car rev up faster. Noticed a big difference with it. quick question. Did you replace all ball studs upper ad lower front and rear. Not having much luck looking for them as I can only find replace the whole control arm. If it was, say Mood. What part numbers
 
OP
OP
Kebin F Friel

Kebin F Friel

Enthusiast
Joined
Mar 25, 2021
Posts
10
Reaction score
4
Location
30019
BadBrad72

Part numbers I have are for the
upper and lower control arm energy bushing kit 22310 (1) $110.08
Front Upper Ball Joint 22310 (2) $81.65
Front Lower Ball Joint 22308 (2) $82.80

ARD Mortor Sports
Lawrenceville, GA
770-965-2322
 

BadBrad72

Enthusiast
Joined
Jun 19, 2010
Posts
12
Reaction score
4
Thank you! Greatly appreciated.

You must be registered for see images attach


You must be registered for see images attach
 

MrLighty

Enthusiast
Joined
Mar 21, 2009
Posts
29
Reaction score
3
Ipsco power steering pulley and bracket. Polyurethane motor and transmission mounts. Replace all suspension bushings with polyurethane. Coil over adjustable shocks. Shift eliminator kit. Short throw shifter. Paint correction.
 
Last edited:
OP
OP
Kebin F Friel

Kebin F Friel

Enthusiast
Joined
Mar 25, 2021
Posts
10
Reaction score
4
Location
30019
Bad Brad, you have my twin. I just scored a soft top with a frame.

MrLightly thank you for the input. Just had the suspension bushing replaced. Adj Coilover is next.

Here are my Dyno results.
New Ball Joints
Belanger Complete Exhaust
K & N Performance Air Intake
SCT X3 Power Flash Programmers
Dyno Tuning

You must be registered for see images attach
 
OP
OP
Kebin F Friel

Kebin F Friel

Enthusiast
Joined
Mar 25, 2021
Posts
10
Reaction score
4
Location
30019
More upgrades
Thank you JonB at viper parts rack for hooking me up w new
You must be registered for see images attach
wheels and tires it drives fantastic
 

usmcfieldmp

Enthusiast
Joined
Apr 16, 2021
Posts
7
Reaction score
6
Location
Fort Worth, TX
Nice, those wheels are a really good look for the car.

Your rotors caught my eye; you should check to see if your rotors are directional (internal vanes). A lot of manufactures tend to make them with the slots meant to sweep forward. Having them flipped won't make them explode, but if you drive canyon roads, autocross, etc - they will heat soak/overheat faster.

You must be registered for see images


The drilled and slotted rotors on my Audi were directional. Passenger Front... front of the car to the right of the picture.

You must be registered for see images attach
 
OP
OP
Kebin F Friel

Kebin F Friel

Enthusiast
Joined
Mar 25, 2021
Posts
10
Reaction score
4
Location
30019
Thank you I will check they came on the car when I got it have not looked that close. Bit I will
 
Top