Sill Scuff Plates - Inner and Outer

[LifeIsGood]

I just spent the last few hours researching inner and outer scuff sill plates, as I'm looking for some outer ones. I recently got these Inner Scuff Sill Plates from Mark at IPSCO...as you can see they can be lasered with your own personal touch...

You must be registered for see images

You must be registered for see images

...as you can see above, my passenger side outer sill plate is showing some wear and I'd like to get some nice heavy duty, non-scuff covers for them also. I've looked at the sponsor/vendor sites and some others. I really like the MGW ones, but I wanted longer ones that would cover most of the outer sill plate area. The other's that I've seen online seem like they would scratch, most have a glossy/polished finish. I'd prefer not to tape them down...I would rather incorporate the current holes with longer screws, maybe.

Anyone have pictures of nice heavy duty outer sill plates installed?

Thanks in advance for your help!

 

[KNG SNKE]

I like those plates. Sharp looking.

 

[JonB]

Sounds like bolt-on Satin Alum, or Black Anodised like Marks, would suit you well...... ZAF makes them. Lazer-engraved area can be Yellow or any other Viper color

 

[GTLaser]

Nice, I have the same ones....

Sounds like bolt-on Satin Alum, or Black Anodised like Marks, would suit you well...... ZAF makes them. Lazer-engraved area can be Yellow or any other Viper color

Problem with Zaf's is they cover the holes to remove exhaust sills.

These are nice ..... http://www.vipairperformance.com/servlet/the-8/Carbon-Fiber-Rocker-panel/Detail

 

[LifeIsGood]

Sounds like bolt-on Satin Alum, or Black Anodised like Marks, would suit you well...... ZAF makes them. Lazer-engraved area can be Yellow or any other Viper color

Jon...I don't see any bolt-on plates...the GEN II looking ones all state...'Peel & Stick '...I can't find any on that site.

 

[LifeIsGood]

Nice, I have the same ones....

These are nice ..... http://www.vipairperformance.com/servlet/the-8/Carbon-Fiber-Rocker-panel/Detail

Those do look very nice, but I would be happy with a non-carbon fiber version if it were a bit cheaper.

 

[LifeIsGood]

I like those plates. Sharp looking.

Thanks! Mark always does great work. I'm not a keep it stock kind of owner...I like the few 'Life is good' stuff I've added to the viper.

 

[happy]

Hey where di you get that little leather pouch on the pas side console?? Was that factory cause i never seen one with it?? Or did you just add it on? I like!!

 

[Jance GTS]

Ken those look good! If you don't mind me asking, what did they cost without the custom engraving?

Can you get some close up pictures? Thanks!

 

[JonB]

Jon...I don't see any bolt-on plates...the GEN II looking ones all state...'Peel & Stick '...I can't find any on that site.

They dont feature bolt-on sills on their site, [nor do we]..... .

 

[JonB]

Hey where di you get that little leather pouch on the pas side console?? Was that factory cause i never seen one with it?? Or did you just add it on? I like!!

That is a Dodge Viper Cupholder ....sunglass holder...cellphone holder

 

[LifeIsGood]

Hey where di you get that little leather pouch on the pas side console?? Was that factory cause i never seen one with it?? Or did you just add it on? I like!!

It's a beverage holder . I bought it from the VCA classifieds a while back. I got it from ViperNM.

 

[mattdillon]

Those do look very nice, but I would be happy with a non-carbon fiber version if it were a bit cheaper.

They are definitely proud of them, most sites I've looked at are mostly for the gen III's on up. Ken, your other ones look nice.

 

[mattdillon]

You must be registered for see images attach

This is first time I've tried to add a pic, so not sure how its going to look. But anyway this is mine.

 

[mattdillon]

Thinking about painting the grooves & viper in black or maybe steel gray.

 

[mattdillon]

You must be registered for see images attach

Here's another pic from a different angle.

 

[eucharistos]

...as you can see they can be lasered with your own personal touch...

man those are cool LIG

 

[LifeIsGood]

Ken those look good! If you don't mind me asking, what did they cost without the custom engraving?

Can you get some close up pictures? Thanks!

The laser engraving cost is included. They are $159.95 on his website, but give him a call...he'll probably work you a VCA deal. Here are some close-ups...

You must be registered for see images

You must be registered for see images

 

[mattdillon]

Ken, I think the one thing that makes them look so good is the font you did. It just kinda says (Everything's Cool & Yea, Life is Good). JMO