Jeff Lemke
Enthusiast
Not sure yet.
Custom Hood Design: Need Feedback
- Thread starter Jeff Lemke
- Start date
Not sure yet.
Jeff Lemke
Enthusiast
It's about 1" higher at the front of the bulge and the rear of the bulge. The center is about the same.
big-n-italian
Enthusiast
holy crap that is cool looking!
any chance of making the back of the center **** a little higher to let out more heat?
(oops - sorry. just saw it was already asked.)
any chance of making the back of the center **** a little higher to let out more heat?
(oops - sorry. just saw it was already asked.)
LS6 Molester
Viper Owner
looks great, like said before i would like the cowl higher
TexasPettey
Enthusiast
Where does the air intake for the AC come in? If I understand correctly, the airbox is under the pass side grill on the stock hood. I ran my car without the airbox for a short while, as I was messing with some placement of fuel pump booster. The AC was useless because it was sucking in hot air from under the hood.
viperchick12
Viper Owner
I like it Jeff Lemke
Enthusiast
The air intake is now a vent but works the same for the airbox. The drivers side is functional for heat extraction.
TexasPettey
Enthusiast
Nice. Is that routing built into the underside of the hood, or is there a new tube required? I couldn't see from the picture where the vent location is relative to the existing grill.
Jeff Lemke
Enthusiast
wastntim
Enthusiast
Looks good!
TexasPettey
Enthusiast
For my part, this is very interesting at less than $4K. I get a lot of under hood heat and would like a solution for clearing it out while keeping good looks. This looks really ****, so I'd like to see it on and painted. Thanks for all the info.
Very nice! Competitive pricing means that it would be a hot seller. Cost of factory Gen 2 Hood in Canada is $28,000. Even a slight front end collision writes the car off. Your hoods could help a few Vipers get back onto the road after being written off.
Ted
Ted
GTS-R 001
Enthusiast
Jeff,
Great work! It is nice to see someone investing the resources and time you do on the products you make. You are a great resource to the viper community.
Steve
Great work! It is nice to see someone investing the resources and time you do on the products you make. You are a great resource to the viper community.
Steve
DSG2003SVT
Enthusiast
It definitely has the potential to look great! I would have to see it on a car before I could decide for sure though. Nice work!
Nadine UK GTS
Enthusiast
Wow! ...Get yourself over to U.K. (ASAP) I have some work for you to do!! Just in primer it looks the nuts, where do we book your ticket from?? 
Viper Fever
Viper Owner
Jeff been thinking about your hood all weekend. Will it work with the stock
air box am VERY INTRESTED.
air box am VERY INTRESTED.
BullRider
Enthusiast
Very interested too! I love that hood! If you're making a list of potential buyers, put me on it! email address is bob(at)replicacountach.com.
Viper Fever
Viper Owner
Jeff thanks for the reply. I love the way my 1995 RT10 looks , the back and side views
are the best but the smoothie hood was always lacking in my opinion. I think that
your hood will compliment the rest of the car very nicely. I'm very excited thank you.
are the best but the smoothie hood was always lacking in my opinion. I think that
your hood will compliment the rest of the car very nicely. I'm very excited thank you.
ViperJay
Viper Owner
Very interesting. Im dealing with the settling cracks on the hood of my 1995 rt/10. for 4k, i might want to ditch the original hood altogether. cant wait to see pics of this finished on a gen1.
dansauto
Enthusiast
post a pic of the crackes or PM me, they can be fixedVery interesting. Im dealing with the settling cracks on the hood of my 1995 rt/10. for 4k, i might want to ditch the original hood altogether. cant wait to see pics of this finished on a gen1.
Disturbed
Viper Owner
I like that hood. It would be a touch choice between this one and your "other" hood for a GenII. I would have to see a pic of them painted and on the car. This hood may not have the curves to match the GEN I/II.
ViperJay
Viper Owner
its the usual cracks for a 1995. i already talked to chuck and he said it has to be taken down to the fiber and built back up before paint. cracks are in the paint, not the hood. but if im already going through that whole process..... this hood looks killer.
Jeff Lemke
Enthusiast
You must have me confused with USExotics. He has a gen 1-2 hood that is very outragous and interesting. It's a popular hood so if you do a search you should be able to find it. I'll post pics of this hood on the car tonight when I'm not on with dial up.
Jeff
Jeff Lemke
Enthusiast
OK, keep in mind there are no latches on this hood so it is only setting into position (hence the poor gaps at the moment).
Disturbed
Viper Owner
I must be mistaken, sorry for that. I do love your street serpent kit
If I had a GENIII I'd put it on in a heartbeat.Maybe it's just the primer but I think the scoop in the center needs a bit more hight oommph to it. The viper body has lots of curves and no hard edged lines. It's VERT difficult to blend curves with hard lines. I think this could work well but needs the curves to match the GenI/II better. So far, so good.
DSG2003SVT
Enthusiast
Let me be the first to say that I think that looks VERY NICE on the car. You do some fine work.
SylvanSRT
Enthusiast
Again another great product and design!
Viper Scot
Viper Owner
I think it's great although I'm very much into FUNCTIONAL scoops and vents (I HATE the hood scoops on the likes of a Mustang that have no functional purpose). This design would therefore be excellent for getting cold air into and hot air out of a forced induction engine bay, something the existing Gen I hood can't do well. Is the air coming in from the duct directed onto any specific area of the engine bay?
Similar threads
