The Build has Finally started.....Pics...

[carl B]

I have a brand new set of ten diamond pistons for a cream puff if anyone needs them???
Carl

 

[RobZilla]

Carl I sent you a PM.

 

[VIPER BAZ UK]

Its alive!!!!!!!!!!!

And LOUD!!!!!!!!

Fired up first time with a BIG cloud of smoke which cleared after a while, Poured a small amount of motor oil in the bores while getting oil presure up with the plugs and fuel pump relay out...

Just needs to go away for a tune......

 

[RobZilla]

Congrats.... what a great feeling that must be.

 

[2001 GTS]

Baz...you ****. jk

Finally got mine started last Thursday, but it looks like at your pace you will have a few miles on it before mine even rolls!

Looking good!!!!

 

[VIPER BAZ UK]

Baz...you ****. jk

Finally got mine started last Thursday, but it looks like at your pace you will have a few miles on it before mine even rolls!

Looking good!!!!

LOL!!!!

Not sure about that only just got the trans back in..
MSD gets wired in Sunday,, Then booked for a tune...

 

[plumcrazy]

congrats Baz, keep us posted and good luck

 

[BOTTLEFED]

good job

keep us updated on it, I want to know since I'm considering swapping my pistons as well

 

[VIPER BAZ UK]

Little tidying up off the wires on the AEM......

You must be registered for see images

 

[VIPER BAZ UK]

Just when you think you are almost there........
You have to start at the back....

BIG Thanks to mate Dave at DK Car Audio & Security - For all his help doing the wireing for the fuel pump booster..
Managed to use a spare relay port in the factory harness.... Had to remove the hole loom out the trunk though... But well worth it...

You must be registered for see images

You must be registered for see images

You must be registered for see images

You must be registered for see images

 

[DAMN YANKEE]

Baz,

Congrats! Great job and one hell of a great looking rig!

Keep after the oil in the charger, change it once a year.

I say dump the airbox and get a PBJ unit as it would look great with your engine.

Fine indeed!

 

[BOTTLEFED]

Baz, if you check out my thread on installing the BAP I also mounted it in the trunk. I thoguht of using that extra relay port in that box but thought it would be too much hassle to pull it out. Go to know it is possible.

Everything is looking great

 

[VIPER BAZ UK]

Baz, if you check out my thread on installing the BAP I also mounted it in the trunk. I thoguht of using that extra relay port in that box but thought it would be too much hassle to pull it out. Go to know it is possible.

Everything is looking great

Its all your fault LOL!!!!!
I folowed your instructions .....

 

[InjectTheVenom]

Hi Baz,

Good work! Isn't it fun to crawl through a wiring diagram in search of the right wires that reaches a rush of satisfaction once everything works ? A few weeks ago I installed a turbotimer by me onesies (had trouble locating the speed signal, only to find out that the frequency is too high for the timer I ordered) and the previous weekend had me installing the wiring loom for two gauges.

 

[VIPER BAZ UK]

Now thats neat and tidy......

You must be registered for see images

You must be registered for see images

 

[BOTTLEFED]

very nice and clean



BTW, where is the rear carpeting?

 

[VIPER BAZ UK]

very nice and clean



BTW, where is the rear carpeting?

In the kitchen at the moment....

 

[BOTTLEFED]

I've never liked carpeting in the kitchen, I'm more of a hardwood floors kinda guy

 

[VIPER BAZ UK]

The Push Rod length was 7.55......

Bit of a set back because the AEM COMMS lead is faulty...