Search results

  1. M

    replacing fuel pump gen 1 , have the pump out have some questions

    got gen 2 injectors , thanks
  2. M

    replacing fuel pump gen 1 , have the pump out have some questions

    any body ? would like to reassemble in the morning . thanks to all
  3. M

    replacing fuel pump gen 1 , have the pump out have some questions

    got the pump out not as bad as i thought it would be , replacing the original bosch pump with a walbro 225. my question is do i leave off the origional round filter on the bottom and remove the bottom of the canister with the disc and rubber insulator that the fuel pump rest on and just install...
  4. M

    inner fender well removal

    i got it almost off, do i have to drill the 2 rivets on the dog leg out, looks like the only thing holding it in place , left rear [ replacing fuel filter ] thanks to all car is a gen 1
  5. M

    anyone blend e85 with gas , thoughts , formula for mixing , ideas

    thought about this at work today , i would think 4 gallons of e85 and fill the rest up with 10% 91 octane would raise the octane level since e85 is 105 octane , then recalibrate my vec 2 . thanks to all
  6. M

    The RT/10 surprised me at the track yesterday

    its called testicle fortitude some have it some don't
  7. M

    thoughts on striping a gen 1 , any photos to post

    here is the car. trying to post photo but it is to big , old man needs help .
  8. M

    thoughts on striping a gen 1 , any photos to post

    thinking of striping my red gen 1 , would like to see what others have done . any ideas would be helpful thanks to all
  9. M

    replaced roller lifters with dc lifters still have a barking noise after warmed up??

    Re: replaced roller lifters with dc lifters still have a barking noise after warmed u called dan and got some tips , clutch was fine . going to get it in the air and check further .
  10. M

    replaced roller lifters with dc lifters still have a barking noise after warmed up??

    Re: replaced roller lifters with dc lifters still have a barking noise after warmed u just went out for a 2 hour drive . the noise is a squeaking noise , i don't think it is engine related now . it stays a constant sound, rpm doesn't doesn't cause the sound to speed up or get louder. what...
  11. M

    replaced roller lifters with dc lifters still have a barking noise after warmed up??

    Re: replaced roller lifters with dc lifters still have a barking noise after warmed u greg good what are your thoughts
  12. M

    replaced roller lifters with dc lifters still have a barking noise after warmed up??

    have a barking noise sounds like internal , removed the serpentine belt still here it , replaced the factory lifters with dc Johnson rollers . ran it yesterday and still here the noise . have a greg good spec cam with 601/607 lift . have 440 lbs. open pressure . could this be to much??> also...
  13. M

    Throttle hesitation 97' GTS

    check tps sensor , use meter to check voltage , could have an open spot . closed should be under 1 volt and go up to just under 5 volts . gradual open the throttle body and watch the voltage increase , if your meter drops in voltage or goes blank it is bad . good luck
  14. M

    Who would like a T-shirt....................

    let me know a price on an ex. large thanks
  15. M

    need lifters. what are the ones to buy

    1994 with 3,800 miles lot's of mods
  16. M

    need lifters. what are the ones to buy

    sounds like i have a lifter barking , going to replace all to make sure i get the bad one , what are the best quality lifters to run . if you have a part number that would be helpful thanks to all
  17. M

    Is there any way to get the ac motor to blow harder?

    my 94 uses 134
  18. M

    GEN1 Dyno Results :-)

    it is piggy backed in with the origional , to controll fuel and timming
  19. M

    temp sending unit ?

    does the push on connector temp. sending unit on the right head on a gen 1 , have any real function
  20. M

    On a 1994 RT-10..besides just repalcing a K+N filter, smooth tubes in stock housing.

    Re: On a 1994 RT-10..besides just repalcing a K+N filter, smooth tubes in stock hous pm sent email me mrbob
  21. M

    First run-in with police in my Viper, not fun at all!

    took my red gen 1 out today i'am on the border of iowa and ill. had cops follow me in ill then went to iowa and 2 more followed me around i did not get pulled over but they were all over me so i put my car away and called it a day .
  22. M

    Fuel in the midwest 93 with ethanol or 91 octane with no ethanol ??

    would like opinions on todays fuel which is recomended for a modded gen1 thanks to all
  23. M

    OBD1 Connector on 94

    look by the a/c dryer ,it is a blue connector with a black cover
  24. M

    what number pin on a vec 2 is the pwm scoket -5v output

    mine pulled out and i forgot what socket it went in . gettin old i guess thanks to all
  25. M

    vec 2 tuning for a gen 1 with g g cam and heads

    i can log just not air /fuel , have been adjusting on the fly with a laptop while driving

Latest posts

Members online

Total: 1,081 (members: 5, guests: 1,076)

Forum statistics

Threads
153,644
Posts
1,685,209
Members
18,220
Latest member
ROIII

Share this page

Top