Search results

  1. R

    Wondering about the headgasket problem?

    Possible, but you can look at the gasket ant tell if it is the old 'filer' gasket. If it has been replaced, I can't imagine anyone replacing the gaskets with the same old 'fiber' gaskets - although stranger things have happened, I guess. Here is a picture of the OLD 'fiber' gaskets with coolant...
  2. R

    Where can I get 3.55 gears?

    JonB at PartsRack, http://partsrack.blastmart.com/customer/home.php http://partsrack.blastmart.com/customer/home.php?cat=171
  3. R

    Need Hood hinges, can anyone help me out?

    Try: http://www.donscharfautomotive.com/ Or http://www.x2builders.com/default.asp or http://viperpartslarry.com/ Not in any particular order.
  4. R

    Who sells the best chin guard?

    I think you have your answer, but if they don't work out try this:
  5. R

    Gen2 headers for Gen1 good idea?

    You can go to page 2 of my photo gallery and see a couple pictures of the Gen 2 tube exhaust installation (last row of pictures on that page). http://gallery.viperclub.org/showgallery.php/cat/500/page/2/ppuser/21507 Later,
  6. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    I was at the track last week and ran with the newly installed Poly Motor and Trans mounts, as described above. Could I tell the difference, hard to tell except the car seemed to push hard in a forward direction when the throttle was hard applied exiting a corner. One thing for sure, my Gen 2...
  7. R

    Poor Man's Pressure Bleeder

    Jim, Nice design; see picture of mine I built in 2005. The rubber stopper must be held in/on the reservoir, thus requiring 2 people (my wife loves opening the brake lines and watching for new clean fluid). The rubber stopper seals very tight around the tube and does not leak. Yes, around $15 -...
  8. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    99 R/T10, You and I both know there are no guarantees that any piece won't break; but I can tell you, actually you can see the mounts from PolyBushings http://polybushings.com/pages/2469.html have the interlock failure metal as per the Original Dodge mounts dating back many, many years. The...
  9. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Baz, Yes I know, no CC's, BUT on their site, there are some other outlets, and I understand someone ordered from one them and they take CC's. Give one of them a shout. Stocking Dealers Forward Motion (302) 658-2829 Mailing Address: PO Box 30700 Wilmington, DE 19805...
  10. R

    HELP! Last Request - Gen I Shift Light Install

    Tom, I know this is an OLD post, but am looking for a little clarification if you will - please. :) :) You said: Looking in my service manual, I found the tach wire as you described above, but where from the PCM do I find the wire? The PCM connectors from top to bottom are BLACK, WHITE...
  11. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Baz, Thanks for the compliment. The Motor Mounts are $98.00 for the pair + $7.00 shipping = $105.00 Transmission Mount is $20.95 + about $10.00 for handeling/shipping =~$31.00 US Funds Web site: http://polybushings.com/pages/2469.html The Poly Transmission Mount I got from Summit...
  12. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Disturbed, Yes, I remember it well - that was a great 4th of July Parade - will we see you at this 4th Parade? :usa: :usa: :usa: :usa: Later,
  13. R

    Has anyone tried: Redline Shift Warning Module

    Has anyone tried to adapt this AUDIBLE RPM indicator to a Viper? http://www.modifry.com/products/rlb/Redline.pdf I drove a Honda S2000 at the track with this installed, and it is trick; just listen and shift. The instructions don't indicate the Tach signal voltage necessary, or how to...
  14. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    klamathpro, Did you get your Motor Mounts yet? It sounds like you will be awhile before you get them installed and running with your engine all apart? Later,
  15. R

    Raptor Shiftlight Install on a Gen 1.5

    Guys, So now the question becomes, which do you trust more, the Shift Light, or the on board Tach (my choice)? I have hit the rev limiter (6200 rpm) a time or two and the tach is right there. The dials on the shift light do not even need to be there , they are only relative. Just set the dials...
  16. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    klamathpro, Oh, yes, no problem. Mine was done last week on a lift, and the engine was stabilized with a long floor standing screw jack and a small 2 x 4 under the front of the pan. Mounts were loosened and the engine was then lifted. Did not remove the trans mount until after the engine mounts...
  17. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Bill B, Yes, the parts catalog calls for the same part numbers. LAter,
  18. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Oh, you will be amazed.
  19. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    klamathpro, I know they have some 'dealers' around the country listed on their web site, and that is a good alternative. Since I am so close (about 400 miles) and I conferred with Johnny directly, I went ahead an got mine via money order. Later,
  20. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    Ya, I know, but no problem, where are you located?
  21. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    klamathpro, As Mark said: DEFINITELY consider poly motor mounts: http://polybushings.com/pages/2469.html Later,
  22. R

    Raptor Shiftlight Install on a Gen 1.5

    alliga, You seem to be correct; check this link, instruction #6. http://forums.viperclub.org/showthread.php?t=573889 It says yellow/gray Later,
  23. R

    Raptor Shiftlight Install on a Gen 1.5

    V10SpeedLuvr, Please post your results. As malcoll said, it seems pretty clear for us Gen 1.5 guys. Later,
  24. R

    Race Brakes: What do you racers use?

    Purdue_Boiler_Viper, As you can see from Tom's graph, the Gen 2 ABS is a good braking system, balanced with maybe a little rear bias. Your best bet, since you said ".....won't see much track time", put on Stainless Steel brake lines, and some good brake fluid (Motul 600, for example). OKViper...
  25. R

    Viper Polyurethane Engine Mounts and Transmission Mount

    All, Just for clarification, the Summit Racing Transmission mount is not "PLASTIC" as suggested. http://store.summitracing.com/partdetail.asp?autofilter=1&part=ENS%2D3%2D1108G&N=700+400008+300537+115&autoview=sku It is made by Energy Suspension and is polyurethane...

Latest posts

Members online

Total: 1,678 (members: 7, guests: 1,671)

Forum statistics

Threads
153,644
Posts
1,685,209
Members
18,221
Latest member
tractor1996

Share this page

Top