Search results

  1. L

    01 GTS radiator hose question

    If I’m correct factory or aftermarket rubber hoses have not been available for years and therefore people get silicone
  2. L

    01 GTS radiator hose question

    Tension clamps are much better. As the name implies they provide a constant force. Screws type, due to the compression of the rubber material in the hose, need to be periodically checked/tightened Also, most of them, due to the design, have a tendency to cut/damage the hose surface
  3. L

    01 GTS radiator hose question

    Bad idea and very poor workmanship If needed, you can bleed the system by disconnecting 1 hose at the heater valve located on top of the hvac box on the passenger side
  4. L

    Trim Screw 06035625 Junkyard Scavenging

    Give me your address and i will mail you 1
  5. L

    Trim Screw 06035625 Junkyard Scavenging

    I bought a few 21 years ago As a matter of fact i bought a bunch of different screws, bolts , plastic caps,etc. glad that i did then
  6. L

    need a viper tech in Fresno

    No. Which year is your viper and what do you need to be done ?
  7. L

    From what Material is the floor section made on a GTS Gen 2?

    It’s steel for sure Removing the door jamb trim to pull the carpet is easier said than done because the plastic trim is retained by screws that hide behind some plastic plug/cap that cannot be removed without any damage to the plug or trim and they have been nla for a very long time
  8. L

    3D print an interior door sill plug

    My mistake, the correct part # for the small plug on the inner sill is:MB68DX9
  9. L

    3D print an interior door sill plug

    Can you make a few and i buy them from you ? Thanks
  10. L

    3D print an interior door sill plug

    they were serviced, part # 4848881AA, but have been NLA for years. they go on top of the screws holding the sill cover interior
  11. L

    3D print an interior door sill plug

    that would be fantastic if you could. Mopar part # was 4848881AA
  12. L

    3D print an interior door sill plug

    I’m talking about the smaller plugs on the plastic trim inside the car. To the right in your pictures
  13. L

    3D print an interior door sill plug

    Dan, do you have any idea for the plugs on the plastic trim on the inside sill ? You can’t remove them without damaging them and they have been nla for years
  14. L

    need a viper tech in Fresno

    as the title say, I need a viper tech in Fresno for my 00GTS Thanks
  15. L

    Still Loving my 2000 RT/10 after over 20 yrs

    Lol, still alive!!!
  16. L

    Still Loving my 2000 RT/10 after over 20 yrs

    Same here. Bought my 2000 gts brand new 23 years ago and the excitement of driving it is the same than day 1 21k miles
  17. L

    Experience on door sag/hang up on GTS

    No, try to picture it, the body flange is the male part and the u channel on the back of the weatherstrip is the female part. You file down the flange. Just pull up the weatherstrip, once you see what I’m taking about, it’s pretty obvious
  18. L

    Experience on door sag/hang up on GTS

    You don’t completely remove the weatherstrip, you just lift the bottom part a few inches on both side of the safety latch There is no adhesive on that part of the weatherstrip, it’s just a U channel with metallic clips encased in the rubber that grip the body flange
  19. L

    Experience on door sag/hang up on GTS

    I bought my 00 GTS brand new and had the same issue right from the beginning. Fix was very simple, remove weatherstrip and file down the lip/seams that the weatherstrip sit on By doing so you lower the weatherstrip and fix the problem. Just file a little bit at the time and try until you get it...
  20. L

    Searching For A GTS

    Prices are certainly going up so don’t wait too long I bought my 00 Gts , black with silver strips brand new and I just can see parting myself with it
  21. L

    Advice on 1999 GTS Purchase with title issues

    Original ACR/BBS wheels were 18", not 19". It's all depend on your financial situation, you are not going to find a "no issue" Gen2 for low to mid 20, so if you can't afford to spend more money, buy it and enjoy it.
  22. L

    Advice on a Gen II GTS

    from an old thread: 03-15-2007#29 Bill Pemberton Woodhouse VCA Member Midwest Supporting Vendor Join DateJul 2000LocationBlair,Nebraska,USAPosts5,084 Re: Are 2000\'s really the fastest?Sorry, Rogue, but you are falling for the hype that was perpetuated by the Forged Piston crowd. Folks have...
  23. L

    Advice on a Gen II GTS

    ....and was the fastest Gen2 year
  24. L

    Viper Track Event at Buttonwillow Jan 17-18, 2015

    Sure can: let assume that the break even point is reached at 55 drivers. Make sense since it what they say they need to run the event. Between the entry fee from those 55 drivers ( $21,725) and the "sponsorship money" referenced by Dan in it's post, all costs, the ones I listed + West coast...
  25. L

    Viper Track Event at Buttonwillow Jan 17-18, 2015

    Seems to have touched a raw nerve here.... AZTVR: There must be at least 500 events going on every year at California 7 road racing tracks. Do you really think that 1 or even a few more will make any difference? Did I try to advertise the name of my business? Nope. So that has nothing to do...

Latest posts

Members online

Total: 1,492 (members: 3, guests: 1,489)

Forum statistics

Threads
153,644
Posts
1,685,209
Members
18,220
Latest member
ROIII

Share this page

Top