Search results

  1. R

    curious about 08 viper exhaust system

    Good point. remember the new variable ratio camshaft will have a ton of influence on the exhaust note, therefor it will be hard to duplicate in a Gen 3. Robbie
  2. R

    Poly motor/trans mounts

    Everyone is quite correct in that you should ether remove the side sill and disconnect the cat mounts before you raise the engine to change the mounts. Another option would be to remove the V clamps between the exhaust manifold and the RT cat header pipe. I have done it both ways. Robbie
  3. R

    Need Pan Head Torx bolts to hold 5 points belt

    If you go to my web site below and click on the Parts Book for 2003 you should be able to find the part number. http://www.members.aol.com/AtroRacingTeam/PRODUCTS/AtRoRacingsProductCatalog Robbie
  4. R

    Looking for piping to replace factory cats

    The v clamp is reusable.
  5. R

    Red Line Power Steering Fluid, how to do, where to get ?

    Dan, Thank you for the confirmation. I have a 2003 with the original fluid with zero problems. Robbie
  6. R

    Stock oil pans?

    Price including shipping?
  7. R

    Red Line Power Steering Fluid, how to do, where to get ?

    I believe the proper power steering fluid is as follows but I am not 100% sure. Can anyone confirm this? MOPAR 04883077 POWER STEERING FLUID, CLEAR TYPE, MS-5931 Robbie
  8. R

    oil pressure

    I would go back to who installed the pistons. did they check the clearance between the piston and the cylinder? Is the cylinder out of round? Did they hone the cylinder?Did they check and adjust the piston ring gap. perhaps they installed the rings wrong. What about the crankshaft bearing or the...
  9. R

    Nail in tire - SRT10

    Just to note that I have repaired both rear tires and have 5000 miles on the repair with the kit above. This kit has rubber plugs that are shaped like a mushroom. The mushroom head is injected from outside of the tire into the inside of the tire with the gun included in the kit. There it expands...
  10. R

    EBC Redstuff Brake Pads

    I received the brake pads in perfect condition from Voi9, Phil, yesterday. He was true to his word and shipped them out as agreed. I would recommend doing business with him anytime as he is a stand up guy. Robbie
  11. R

    Is this a good tire gauge?

    As far as I am concerned Longacre Racing makes the best products as Kai SRT10 said above. Robbie
  12. R

    Nail in tire - SRT10

    I use this NAPA kit to plug my tires. Michelin says not to plus run flats. This is why I run Non Run Flats.710-1637 FLAT TIRE REPAIR KIT Robbie
  13. R

    VCA Monroney Window Sticker Replacement Program

    I never would have thought I would need to "Add special instructions to seller". the instructions did not mention that from what I remember.. But my memory is a little shady in my old age! The good part is that it is on order and paid for! Robbie
  14. R

    WTF??? Smoke and fire!

    And just think, I was leading with 2 laps to go and a 10 car lead. I was so mad I sold the whole Late Model operation on the spot to two New York City detectives. But there was a bright side to all of this. Coors gave away a case of beer for every lap led. hell I won 98 cases of beer. Coors took...
  15. R

    WTF??? Smoke and fire!

    I feel sorry for you. While this has not happened to your viper I had a racing Fram oil filter gasket let go in my NASCAR Late Model at The Race Of Champions at Pocono about 10 years ago. The gasket was not seated properly in the oil filter and it exploded like a grenade. The engine followed 2...
  16. R

    Red Line Power Steering Fluid, how to do, where to get ?

    If my viper was under warranty I would use what the factory specifies. Seeing there have been recalls and TSB's on the power steering systems in our vipers I would stick with the factory Mopar part number. Be aware as posted above that there are 2 types of fluid used on 2003 vipers, and perhaps...
  17. R

    Driving a viper with the exhaust changed = automatic ticket

    Here in CT they have to prove you are louder than the state mandated noise limit. I always carry a Sound Level Meter, Radio Shack 33-2055, and a copy of the CT Statues showing the DBA levels and how they are to be measured. I got out of the ticket but one time. I had bought a brand new Honda...
  18. R

    2.5" exhaust vs 3" exhaust

    In the interest of saving you money I would but a set of RT 3" cats with metal substrate core. These 3" RT Cats are a stock item where the 2-1/2" need to be made up custom by RT. I would then buy 2 - WALKER 41974 EXHAUST PIPE REDUCERS, 3" ID X 2-1/2" OD, and install them between the 3" RT cats...
  19. R

    Red Line Power Steering Fluid, how to do, where to get ?

    Summit has it in stock too. Robbie http://store.summitracing.com/partdetail.asp?autofilter=1&part=RED%2D30404&N=700+400236+115&autoview=sku
  20. R

    gauge pods for SRT10

    Those are really nice and much needed. A nice product at a fair price! My only concern would be the chance of the driver hitting his head on them in a violent accident. One would be amazed how far your body moves in an accident even with a racing harness. Robbie
  21. R

    170 thermo

    I do not think the Spal unit will work with the SRT hydraulic fan. The ECM controls a relay that turns the hydraulic fan on. The trick is to use a Adjustable Fan Control to bypass the ECM harness at the relay. The unit I was working on uses it's own temperature probe. It attached where the...
  22. R

    Gen 3 throttle body

    Looking forward to seeing to results. Robbie
  23. R

    2008 engine parts fit all Gen 3's

    Guys, If you want the answer to the big question they go to your summer issue of viper magazine on page 9, center column, last paragraph. In short Kipp Owen, Director of SRT, says the heads, clutch, pressure plate, transmission, flywheel, and rear axle will fit the 2003-2006 SRT10 vipers...
  24. R

    170 thermo

    ViperTony, I have a controller in the works that I was working on but I shelved it as I did not have time to finish it. It would use an adjustable fan control which would piggyback to the fan control relay. If there was enough interest here I would finish the project. The control is finished...
  25. R

    Gen 3 throttle body

    Gary, What can one expect for engine hp and torque increases on a bone stock engine with no mods? Robbie

Latest posts

Members online

Total: 1,357 (members: 8, guests: 1,349)

Forum statistics

Threads
153,663
Posts
1,685,351
Members
18,254
Latest member
Puntacanaviper

Share this page

Top